최신Juniper Service Provider, Professional (JNCIP-SP) - JN0-664무료샘플문제

A. It creates a BGP multihop neighborship between two PE routers.

B. The PEs exchange Type 1 OSPF LSAs instead of Type 3 OSPF LSAs for the L3VPN routes

C. The PEs exchange Type 3 OSPF LSAs instead of Type 1 OSPF LSAs for the L3VPN routes.

D. It creates an OSPF multihop neighborship between two PE routers.

A. You expect a silent discard.

B. You expect the ping results to be fragmented.

C. You expect an echo reply.

D. You expect an ICMP message too long error.

A. This value is used to add a target community to BGP routes advertised to the remote PE device.

B. This value is used to identify BGP routes learned from the local CE device.

C. This value is used to identify BGP routes learned from the remote PE device.

D. This value is used to add a target community to BGP routes advertised to the local CE device.

A. You must use the RIB group to move a default route, which is learned through BGP, from the inet. o table to the VPN-A. inet. 0 table.

B. You must use the RIB group to move interface routes from the inet . 0 table to the VPN-A. inet. 0 table.

C. You do not need to use the RIB group to move interface routes from the inet. o table to the VPN-A.
inet. 0 table.

D. You do not need to use the RIB group default route, which is learned through BGP, from the inet. o table to the VPN-A. inet. 0 table.

A. Change the local address on R2 to be higher than R3.

B. Change the group-range to be more specific on R2 than R3.

C. Change the bootstrap priority on R2 to be higher than R3

D. Change the default route in inet.2 on R4 from R3 as the next hop to R2

A. Behavior Aggregate Classifier -> Multifield Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Scheduler/Shaper/RED -> Rewrite Marker

B. Behavior Aggregate Classifier -> Input Policer -> Multifield Classifier -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Scheduler/Shaper/RED -> Rewrite Marker

C. Multifield Classifier -> Behavior Aggregate Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Output Policer -> Rewrite Marker -> Scheduler/Shaper/RED

D. Behavior Aggregate Classifier -> Multifield Classifier -> Input Policer -> Forwarding Policy Options -> Fabric Scheduler -> Scheduler/Shaper/RED -> Output Policer -> Rewrite Marker

A. The excess traffic will be discarded

B. The exceeding queue will be considered to have positive bandwidth credit

C. The exceeding queue will be considered to have negative bandwidth credit.

D. The excess traffic will use bandwidth available from other queues

A. Adjust the Dead Interval on R4 to match the Dead Interval on R1 and R2.

B. Adjust the Priority on R1 to be lower than the Priority on R4.

C. Adjust the Hello Interval on R1 and R2 to match the Hello Interval on R4.

D. Change the MTU size on R1 and R2 to be 22 bytes higher than R4's MTU size.

A. BGP GTSM requires a firewall filter to discard packets with incorrect TTL.

B. BGP GTSM requires a TTL of 255 to be configured between neighbors.

C. BGP GTSM requires a TTL of 1 to be configured between neighbors.

D. You can implement BGP GTSM between R2, R3, and R4

E. You can implement BGP GTSM between R2 and R1.

A. Configure all routers to be L1.

B. Configure the ignore-attached-bit parameter on all L1 routers

C. Configure the ignore-attached-bit parameter on all L2 routers.

D. Configure all routers to allow wide metrics.