Fortinet NSE8_811 : Fortinet NSE 8 Written Exam (NSE8_811)

시험일은 다가오는데 아직 준비가 부족하다고 느끼시나요? ITDumpsKR의 NSE8_811 연습문제는 Fortinet NSE 8 Written Exam (NSE8_811)의 핵심 포인트만 엄선해 65문항으로 압축했습니다. 짧은 시간 안에 집중적으로 실력을 끌어올려 보십시오.

Fortinet NSE8_811 시험 개요:

Fortinet NSE8_811 시험 요강 주제:

Fortinet NSE8_811 응시 전 알아두어야 할 질문들

최신 Fortinet Network Security Expert NSE8_811 무료샘플문제

문제 #1

Refer to the exhibit.

The exhibit shows a full-mesh topology between FortiGate and FortiSwitch devices. To deploy this configuration, two requirements must be met:
* 20 Gbps full duplex connectivity is available between each FortiGate and the FortiSwitch devices
* The FortiGate HA must be in AP mode
Referring to the exhibit, what are two actions that will fulfill the requirements? (Choose two.)

A. Configure the master FortiGate with one LAG and FortiLink split interface enabled on ports connected to cables A and C and make sure the same ports are used for cables B and D on the slave.
B. Configure the master FortiGate with one LAG and FortiLink split interface disabled on ports connected to cables A and C and make sure the same ports are used for cables B and D on the slave.
C. Configure both FortiSwitch devices as peers with ICL over cable E, create one MCLAG on ports connected to cables A and C, and create another MCLAG on ports connected to cables B and D.
D. Configure both FortiSwitch devices as peers with ISL over cable E, create one MCLAG on ports connected to cables A and C, and create another MCLAG on ports connected to cables B and D.

문제 #2

Click the Exhibit button.
What are two ways to establish communication between an existing NAT VDOM and a new transparent VDOM? (Choose two.)

A. Set type ethernet to the vdom-link, vlink2.
B. Set the not ip 10.I0.I0.1 command to vlink20.
C. Set type ppp to the vdom-link, vlink2.
D. Set the set ip 10.10.10. i command to vlink2l.

문제 #3

You cannot the FortiGales default gateway 10.10.10 .1 from the FortiGate CLI. The FortiGate interface facing the default gateway is wan 1 and its IP address 10.10 .10 K74 During the troubleshooting, tests, you confirmed that you can plug other IP addresses in the 10.10.10. 0/24 subnet from the FortiGAte CLI without packets lost.
Which two CLI commands will help you to troubleshoot this problem? (Choose two.)

A. diagnose debug flow filter saddr 10.10.10.1
diagnose debug flow trace start 10
B. diagnose ip arp list
C. diag sniffer packet wan1 'arp and host 10.10.10.1'
D. diagnose hardware deviceinfo nic wan1

문제 #4

Exhibit

Click the Exhibit button. The exhibit shows the steps for creating a URL rewrite policy on a FortiWeb. Which statement represents the purpose of this policy?

A. The policy redirects all HTTP URLs to HTTPS.
B. The policy redirects all HTTPS URLs to HTTP.
C. The policy redirects only HTTPS URLs containing the ˆ/ (. *) S string to HTTP.
D. The pokey redirects only HTTP URLs containing theˆ/ ( .*)S string to HTTPS.

문제 #5

Click the Exhibit button.

Your company has two data centers (DC) connected using a Layer 3 network. Servers in farm A need to connect to servers in farm B as though they all were in the same Layer 2 segment. What would be configured on the FortiGates on each DC to allow such connectivity?

A. Create an IPsec tunnel with transport mode encapsulation.
B. Create an IPsec tunnel with VLAN encapsulation.
C. Create an IPsec tunnel with Mode encapsulation.
D. Create an IPsec tunnel with VXLAN encapsulation.

질문과 대답: