최신Juniper Service Provider Routing and Switching, Professional (JNCIP-SP) - JN0-660무료샘플문제
문제1
Refer to the exhibit.
In a newly configured VPLS network, you see the output shown in the exhibit. The remote PE is
10.1.1.2. What is the cause for the OL status?
Refer to the exhibit.
In a newly configured VPLS network, you see the output shown in the exhibit. The remote PE is
10.1.1.2. What is the cause for the OL status?
정답: B
문제2
Click the Exhibit button.
You are the administrator of AS 65000. In the exhibit, there are four links between your network (AS 65000) and your upstream provider (AS 65001). You have an export policy on all of your routers to advertise your routes such that: Router A.
MED 100, AS Path (65000), Origin 1 Router B.
MED 100, AS Path (65000 65000), Origin 0 Router C.
MED 50, AS Path (65000 65000), Origin 1 Router D.
MED 50, AS Path (65000), Origin 0
Through which link will traffic from the Web server enter your network (AS 65000)?
Click the Exhibit button.
You are the administrator of AS 65000. In the exhibit, there are four links between your network (AS 65000) and your upstream provider (AS 65001). You have an export policy on all of your routers to advertise your routes such that: Router A.
MED 100, AS Path (65000), Origin 1 Router B.
MED 100, AS Path (65000 65000), Origin 0 Router C.
MED 50, AS Path (65000 65000), Origin 1 Router D.
MED 50, AS Path (65000), Origin 0
Through which link will traffic from the Web server enter your network (AS 65000)?
정답: D
문제3
You have recently configured an aggregated Ethernet interface between two devices in your network. The member links do not all reside within the same PFE complex. You must ensure that the bandwidth and burst size defined in a policer applied to this aggregated Ethernet interface are properly enforced when the traffic falls out of profile.
Which configuration parameter should you use?
You have recently configured an aggregated Ethernet interface between two devices in your network. The member links do not all reside within the same PFE complex. You must ensure that the bandwidth and burst size defined in a policer applied to this aggregated Ethernet interface are properly enforced when the traffic falls out of profile.
Which configuration parameter should you use?
정답: C
문제4
Click the Exhibit button.
A customer is using the Layer 3 VPN multicast technology shown in the exhibit. Which statement is true?
Click the Exhibit button.
A customer is using the Layer 3 VPN multicast technology shown in the exhibit. Which statement is true?
정답: C
문제5
Which statement is true about IS-IS?
Which statement is true about IS-IS?
정답: D
문제6
-- Exhibit -
-- Exhibit -
Click the Exhibit button.
Your network has multiple LSPs between Router A and Router B, as shown in the exhibit. You add a new LSP between these routers with the following parameters:
LSP5: 20 Mbps; Priority 4 3
Assuming no link has 20 Mbps available, which LSP will be preempted by LSP5?
-- Exhibit -
-- Exhibit -
Click the Exhibit button.
Your network has multiple LSPs between Router A and Router B, as shown in the exhibit. You add a new LSP between these routers with the following parameters:
LSP5: 20 Mbps; Priority 4 3
Assuming no link has 20 Mbps available, which LSP will be preempted by LSP5?
정답: C
문제7
You are setting up MPLS RSVP LSPs between R1 and R6 through your core network. You must ensure that the R1 has redundant ERO paths. You must also ensure that both paths are signaled and ready for traffic.
Which action will accomplish these requirements?
You are setting up MPLS RSVP LSPs between R1 and R6 through your core network. You must ensure that the R1 has redundant ERO paths. You must also ensure that both paths are signaled and ready for traffic.
Which action will accomplish these requirements?
정답: A
문제8
Click the Exhibit button.
Referring to the exhibit, PE2 requires the loopback of PE1 to appear in the inet.3 routing table as a labeled route. Which configuration parameter is specifically required to support this?
Click the Exhibit button.
Referring to the exhibit, PE2 requires the loopback of PE1 to appear in the inet.3 routing table as a labeled route. Which configuration parameter is specifically required to support this?
정답: C
문제9
Which configuration parameter would be used by a commit script to use custom syntax and simplify the configuration?
Which configuration parameter would be used by a commit script to use custom syntax and simplify the configuration?
정답: D
문제10
You have recently deployed an MPLS network using CSPF with its default settings. Which statement is true regarding path selection when multiple candidate paths exist?
You have recently deployed an MPLS network using CSPF with its default settings. Which statement is true regarding path selection when multiple candidate paths exist?
정답: C
문제11
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
Referring to the exhibit, you must advertise the 200.100.0.0/16 routes from Site 2 to Site 1, but R3
is not currently advertising any BGP routes to R2.
Why is this happening?
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
Referring to the exhibit, you must advertise the 200.100.0.0/16 routes from Site 2 to Site 1, but R3
is not currently advertising any BGP routes to R2.
Why is this happening?
정답: C
문제12
An IS-IS level 1-only router is configured within a larger multilevel hierarchy. Which OSPF area type resembles the routing information in the L1 router's table?
An IS-IS level 1-only router is configured within a larger multilevel hierarchy. Which OSPF area type resembles the routing information in the L1 router's table?
정답: D